|
Product |
General Description |
Features |
|
VMF
Wall Mount Attachment
|
The vertical
mounting of an IQAir® unit may be desirable in areas where
floor space is scarce or the unit would present an obstacle
on the floor. The vertical mount may also improve the air
cleaning performance for air pollutants with a rising flow
pattern, such as tobacco smoke. If directly mounted above an
air pollution source, the IQAir filtration device helps to
capture rising dust, fumes or vapors |
The VMF allows to mount an IQAir®
filtration system on virtually any structurally sound vertical
surface. The VMF is compatible with all IQAir® models and is
designed to compliment the elegant IQAir® look. |
|
InFlow
W125
InFlow Ducting Attachment
|
The InFlow W125 ducting kit enables
any IQAir filtration system to draw air through a wall or window
vent into an indoor environment. Use of the InFlow W125 is
advisable when the main pollution source is located in adjacent
indoor environments or outdoors. |
Diluting
polluted air with clean air flushing out air pollutants
reducing influx of new outside pollutants due to a build- up
of positive pressure by increasing oxygen content in indoor
air (when outdoor air is being drawn in) |
|
OutFlow
W125
Outflow Ducting Attachment
|
The supply of filtered air into
an environment helps reduce air pollution in that
environment by dilution and the creation of positive
pressure, which reduces the infiltration of polluted air
from outside the environment. With the OutFlow W125 kit, the
filtration device is positioned outside the clean area or
cleanroom, saving valuable space and reducing noise
exposure. It also eliminates the danger of housing leakage,
making it suitable even for certified cleanrooms. |
The OutFlow W125
kit allows filtered air from any IQAir® filtration device to
be directed through a wall or window vent.
The OutFlow W125 kit can be used to:
Create clean areas
Deliver filtered air into cleanrooms or to the outside
Create negative pressure areas Create positive
pressure areas |
|
Mobility 56
Raisers with casters
|
The Mobility 56 kit adds
mobility to any IQAir® system. It also optimizes air
circulation patterns in any environment by raising the
filtration unit's air intake by 4.25" inches off the ground.
No tools or assembly are required to attach the Mobility 56
base extension kit. Simply slide the base blocks into the
filtration unit's base and tighten four wing nuts.
If mobility is not required, the casters are
easily removable. |
Compatible with all IQAir filtration devices. Not compatible with
the FlexVac and VM FlexVac accessories. |
|
PF40
Additional Coarse Dust Pre-Filtration
|
For environments with elevated
levels of coarse dust, the PF40 kit can be added to any
IQAir® system for superior coarse dust filtration. This
helps to extend the life of the unit’s standard pre-filter
element. |
The PF40 kit consists of an upper grille which screws into the
filtration device’s base. A synthetic coarse dust filter pad is
held in place by a lower grille that is secured by four clips. The
1/2 inch deep non-woven design of the PF40 filter pad ensures
superior coarse dust holding capacity.
The filter pad may be washed several times before it needs to be
replaced. |
|
VM FlexVac
Wall Mount Attachment with Source Capture Device
|
The VM FlexVac consists of a vertical mount fixture combined with
a flexible extraction duct system. The suction duct of the VM
FlexVac may be bent, twisted and turned into virtually any
position and will remain in place until repositioned. It is made
from shatterproof, chemically resistant polypropylene. Its large
5” diameter ensures low pressure drop and exceptionally high
suction volume. At a typical air flow rate of 150 cfm the air
velocity within the duct is approx. 12 mph or 17 ft/s. The remote
control, which is supplied with each IQAir filtration device,
ensures convenient operability even when the control panel is out
of reach. |
The VM FlexVac converts any IQAir®
filtration device into a wall-mounted, self-contained extraction
system that allows to capture fumes, dust and vapors at the
source. |
|
FlexVac
Mobile Source Capture Device
|
The FlexVac kit converts any IQAir®
filtration unit into a mobile self-contained extraction system
that allows to capture gases, fumes, vapors, odors and dust
particles directly at their source. |
The FlexVac kit has exceptional direct source capture power for a
system of its size and reach. At a typical air flow of 150 cfm the
air velocity in the suction duct is approx. 17 ft/s or 12 mph. |
